English | 添加收藏 | 设为金沙电子游戏官方入口
您所在的位置:金沙电子游戏官方入口 > > 产品中心 > 弹性体材料 > TPE热塑性弹性体EPDM/PP热塑性弹性体 EP-3000
EPDM/PP热塑性弹性体 EP-3000
Thermoplastic EPDM/PP Elastomeric Compound...
型号:0

参考价:¥

说明:如您对该产品感兴趣,请在此输入您的手机号将本产品的地址 发送至您手机上。
Product Description 产品描述
EP-3000 series are dynamic vulcanized compound by EPDM and PP. It is also called thermoplastic TPV. They has various excellent properties such as good climate-resistant (UV, ozone, sunshine, rain), anti-aging, anti-moisture, chemical resistant (acid, alkali, alcohol, ether) and electrical property. Their cold-resistant property is very well and can be worked in -40℃~125℃for long time. EP-3002 and EP-3003 are medium level oil-resistant. The hardness of the series can reach 75A-40D.
EP-3000是三元乙丙胶与聚丙烯(EPDM/PP)的动态硫化共混物,又称热塑性硫化橡胶(TPV),具有硫化橡胶的各种优异性能,有卓越的耐侯性(紫外线,臭氧,日光,雨水)耐老化,耐水性,耐化学品(酸、碱、醇、醚)和电性能。耐低温性能卓越,能在-40℃~125℃的温度中长期工作。其中3002和3003有中等耐油性。硬度范围可以做到:75A-40D。
 
Product Application 产品用途
l  Insulation and jacketing of DC control cables, rail cables
l  Insulation and jacketing of port machine cables, vessel cables and high-voltage submarine cables
l  Injection mold parts of cables and jacketing of container lorry cables
l  Car rubber parts: seal, exhaust pipes and interior decoration parts
l  Water-proof coiled material of architecture, seal of refrigerator
l  直流控制电缆,轨道交通电缆绝缘和护套
l  港机和船用电缆,高压海底电缆的绝缘和护套
l  电缆注塑件,集卡电缆护套
l  汽车橡胶件:密封条,排风管,内饰件等
l  建筑用防水卷材,冰箱密封条
 
Process Condition 加工要求
Model
牌号
Machine Barrel Temperature
机筒温度
MoldingTemperature
机头温度
Melt Temperature
熔体温度
EP-3000 150 ℃– 190 ℃ 195 ±5℃ 185±5℃
Above data is just for your reference and need to be adjusted according to the actual situation.
以上加工条件只是参考,具体需根据实际情况做适当调整。
 
Dry Condition 干燥条件
No need for drying in normal environment. If the compound was affected with damp, dry it under 90℃conditions for 2-3 hours or under 70-80℃conditions for 3-4 hours. Keep the moisture content smaller than 0.1wt%.
一般不需干燥。如受潮,在90℃条件下干燥2-3小时,或在70-80℃条件下干燥3-4小时,保持树脂含水量小于0.1wt%后再使用。
 
Physical and Electrical Properties   物理及电气性能
Item
试验项目
Unit
单位
Typical Data典型值
EP-3001 EP-3002 EP-3003
Density at 23℃  23℃密度 g/cm3 0.918 1.09 0.95
Hardness  硬度 Share A 92 90 87
Melt Flow Index 熔体流动速率2.16kg×210℃ g/10min 0.39 0.52 ----
Tensile Strength  拉伸强度 MPa 17 15.2 10.2
Spring Back  回弹性 % 43 38 32
Elongation at Break  断裂伸长率 % 542 460 185
Break Set  扯断永久变形 % 104 ---- ----
Compression Set
压缩永久变形
70℃×22hr % 37.5 ---- ----
100℃×22hr % 42 ---- ----
Abrasion
磨耗量(阿克隆)
cm3/1.61kM 0.96 0.62 ----
Ozone Resistance Aging
耐臭氧老化
50×10-8
Tension 20%
40℃×72hr
No crake
无裂纹
No crake
无裂纹
No crake
无裂纹
Low Temperature Impact
低温冲击
-30℃ Pass
通过
Pass
通过
Pass
通过
Brittleness Temperature
脆性温度
-50 -44 -45.5
Air Aging Condition
热空气老化条件
150℃×168h
Variation of Tensile Strength
拉伸强度变化率
% +18.3 +25.5 +15.5
Variation of Elongation
断裂伸长变化率
% -13.7 -14.2 -17.1
Volume Resistivity 体积电阻率 Ω.m 4×1012 2.5×1012 ----
耐油性能
Oil Resistance Properties
 
ASTM 1# Oil
70℃x168h
Retention of Tensile Strength
拉伸强度保持率
% ---- 80 78
Retention of Elongation伸长率保持率 % ---- 79 74
Variation of Volume
体积变化率
% ---- +8.5 +9.6
耐油性能
Oil Resistance Properties
 
ASTM 2# Oil
120℃x24h
Retention of Tensile Strength
拉伸强度保持率
% ---- 51.6 53
Retention of Elongation
伸长率保持率
% ---- 32.2 31.5
Variation of Volume
体积变化率
% ---- 76 72
 

XML 地图 | Sitemap 地图